Farmall International IH 360 414 436 DT466 engine Adapter plate

Description

THE PICTURES OF THE TRACTOR SHOW A DT 360 INSTALLED INTO A 706!!
275 HP AND DOESN'T EVEN BREAK A SWEAT!!
NO; ITS NOT INCLUDED IN THE LISTING HERE
This listing is for an Engine adapter plate!
Built to install the popular AND BIG POWER OF 360, 414, 436, 466 AND 468 IH ENGINES INTO OLDER IH TRACTORS
SUCH AS THE  806, 1206, 756, 856, 1256, 1456, 826
THE 312 AND 360 AND OR DT 360 WILL FIT INTO THE  long frame 706, all 806, 1206 AND the 56 SERIES TRACTORS WITHOUT ANY NEED TO EXTEND HOOD OR FRAME RAILS
MAKES A GREAT REPOWER AS THE ENGINES ARE READILY AVAILABLE FROM AG, IND, TRUCK AND SCHOOL BUS APPLICATIONS!!
OUR ADAPTER WILL ALSO WORK TO HAVE THE 400 SERIES INSTALLED IN THESE SAME APPLICATIONS.
HOWEVER IT ALMOST ALWAYS REQUIRES 4 TO 6 INCHES  INCHES OF FRAME RAIL AND HOOD EXTENSIONS
BUT WHAT A WAY TO MAKE SOME POWER!!
Our plate is built to use factory 12 or 14 inch flywheel,and to use stock IH clutch's OR HYDRO FLEX PLATES
Uses same 14 inch clutch parts as a 1066 OR 1456 1586 and many others.
THE NEW FLYWHEEL IS IDENTICAL TO OEM AND READILY AVAILABLE!!  IT ALLOWS YOU TO USE YOUR STARTER, CLUTCH ETC
ALL ORIGINAL TA ADJUSTMENTS AND CLUTCH CONTROLS CAN BE RETAINED.
This means the CLUTCH parts are available over the counter at your dealer or at any number of aftermarket parts yards and clutch rebuilders.
THIS MEANS OUR HIGH PERFORMANCE TA'S AND  CLUTCHES  FOR THESE MODEL TRACTORS ARE USABLE AS WELL!!
WE ALSO HAVE AN ALL STEEL FLYWHEEL AND TRACTOR PULLING CLUTCH ASSEMBLY AVAILABLE FOR AN
ADDITIONAL COST
IS ABLE TO RUN HIGH RPMS (SFI) AND FEATURES DOUBLE OR TRIPLE DISC ABILITY.
WELL BUILT AND UNMATCHED IN PRICE AND VALUE
SEE OUR OTHER LISTINGS HERE!!
You are in many cases able to retain your sheetmetal (hoods etc) in its original position without modification.
THIS PLATE
WILL ALSO
BOLT ONTO AN M , SM. 400, 450 560 660 AND POSSIBLY SOME OTHERS WITH THE BIG FRAME
BELL HOUSING  BOLT PATTERN LIKE THE 806 ETC.
WE NOW HAVE A 12 INCH  FLYWHEEL WHICH WILL WORK IN THE ABOVE MENTIONED OLDER TRACTOR (PRE 06 SERIES)
YOU CAN RUN A STOCK CLUTCH OR ON UP TO A 24 SPRING PRESSURE PLATE FOR PULLING;  IT WILL PROPERLY RUN YOUR PTO OR HYDRAULIC PUMP
AND ALLOW USE OF YOUR STOCK STARTER IN MOST CASES
IF YOU USE THESE ENGINES  IN THE OLDER TRACTORS YOU MAY NEED TO ADDRESS SOME
FRAME RAIL LENGTH AND WIDTH ISSUES AT THE FRONT OF ENGINE !!
These are made to fit MANY OF the IH tractors AND THEY may well work on some models that are not listed.!!
Generally the cost of overhauling the old D310 and D-361 OR D-407 is what makes folks look at the re-powering with a MORE MODERN IH ENGINE
GETTING THE POWER FROM THE DEPENDABLE 300 OR 400 SERIES ENGINE IS BY FAR THE LEAST EXPENSIVE ENGINE
UPGRADE AVAILABLE IF YOU WISH TO STAY WITH IH POWER
This is also a good way to replace the C263, 291 and 301 gas  found in the  IH tractors
HOWEVER!!
WE NEED TO KNOW IF YOU ARE REPLACING A GAS ENGINE AS THE ENGINE PLATE FOR THIS APPLICATION IS DIFFERENT!
BUT IT WILL PUT YOUR FRAME RAILS IN THE CORRECT SPOT AND ALLOW THE
SHEET METAL TO FIT CORRECTLY!!
BE IT TRACTOR PULLING OR JUST MORE RELIABLE POWER;  IF THE IH ENGINE
HAS WHAT ARE YOU LOOKING FOR
!
HERE IS A PLATE  THAT IS AFFORDABLE AND WILL LOOK LIKE ORIGINAL EQUIPMENT!!!
SEE OUR OTHER LISTINGS FOR INFO ABOUT OTHER UPGRADES FOR IH TRACTORS
717-464-2874
OUR USER NAME HAS A PHONE NUMBER IN IT
888-LEA-MANS IS 888-532-6267
If you are interested in several sets you may wish to call or contact us by e/mail.
Volume discounts available!!